Here it is again. Some improvements to the PPA extraction process were surmised through empirical testing. A mixed solvent system of ethanol and water is now called for, and results in 100% extraction efficiency with super-speedy filtering. This works only for the *non-time-release* tablets,. The time release ones are a different story, I am told, and require much more processing time and crap to deal with.

Some other changes to help clarify the street nomenclature has also been added due to the e-mail I have received. Enjoy, and remember, if you want this to be a *real* FAQ, you guys have to send me more comments.

The 4-Methylaminorex pseudo-FAQ (beta)

Due to strangely increased demand for 4-Methylaminorex "recipes" that I have received by mail, I decided to compile a short document with the cognate preparation of this interesting compound. This may become a full-fledged FAQ in the future, depending on user response and outside input donated where this will undoubtedly be deficient.

     //\
    //  \____ _____ ____CH3
    |   ||   |     |
    |   ||   |     |
    \\  /    O     N
     \\/      \  //
               \//
                |
                N
               / \
              H   H

The numbering starts at the heterocyclic Oxygen and goes counter-clockwise. So the amine is at the 2 position, the methyl is at the 4 position, a phenyl ring is tacked on at the 5 position. Also, the 2-oxazoline part is often merely called oxazoline, as the double bond to the heterocyclic Nitrogen is implied.

It is interesting to note that all of the stereoisomers of 4-MAR are centrally active [1] (ie - it is not stereospecific in action).

Q4. What does Ice/U4Euh do?

A4. The document at Hyperreal.com describing the effects of Euphoria would be a good place to start. Anecdotally, it is said to help concentration and thinking - a sort of "make-you-smarter" drug, with a minor speed-like component to it. Time of action is around 4-6 hours (some say 14-16). Dosage varies but a good start is 20mg for a 150lb individual. It is smoked as the free base or the hydrochloride salt - both have relatively low melting points.

Cognate Preparation of 4-Methylaminorex

Reagents

• Phenylpropanolamine HCl
• Methanol
• Cyanogen Bromide
• Sodium Acetate
• Sodium Carbonate
• Water
• Benzene (or similar)
• Ether

Extraction of Phenylpropanolamine from OTC preparations

1. Extract Phenylpropanolamine HCl (PPA) from OTC diet pills by crushing and dissolving in 5mL ethanol and 5mL distilled water per gram of PPA. Decant solution onto the Buchner funnel and repeat with 2 more volumes of solvent. Use ethanol/water instead of just water because it has less tendency to form a colloid with any cellulosic binders present which would otherwise severely clog the filter paper.
2. Distill off most of the solvent then add cold water to dissolve all of the PPA solids. Basify to approximately pH 9 with 10% Sodium Carbonate or Sodium Hydroxide solution. Extract out PPA base using 3 volumes of ether of approximately 1/3 the volume of water. The ethanol will follow into the ether as well, but very little of the formed salt will.
3. Distill off ether/ethanol for later recovery of the solvents and weigh the amount of solid PPA base, mp 101C. The amount you process here determines, obviously, the amounts of everything else to use later on.

Forming the Oxazoline Ring

The ideal ratio of all the reagents is as follows [2]:

• 1.0 Mole Phenylpropanolamine (MW: 151.2)
• 1.1 Moles Cyanogen Bromide (MW: 105.93)
• 3.0 Moles of Sodium Acetate (MW: 82.04)

The Sodium Acetate may be prepared by carefully adding an equinormal amount of Sodium Hydroxide to glacial Acetic Acid and drying the resultant salt at 120C for 15 minutes.

The preparation of Cyanogen Bromide is covered in another document of mine.

This compound should only be prepared in an area of *adequate* ventillation. A full covering fume hood is ideal (geez - make one, I did) or outside with the wind blowing away from you. Cyanogen Bromide acts on cytochrome oxidase just like any other cyanide and can kill you quite effectively and quickly. Also, it has been known to decompose spontaneously when impure.

1. Dissolve 15g (.142M) of Cyanogen Bromide in 50mL of Methanol at 0C.
2. Dissolve 19.5g (.129M) of Phenylpropanolamine and 31.8g (.387M) of Sodium Acetate in 300mL of Methanol at 0°C. Place this in a round bottom flask equipped with a stirrer magnet and addition funnel.
3. Add the Cyanogen Bromide solution to the flask though the addition funnel over a period of 15 minutes with stirring.
4. React for an additional 45 minutes at 0°C.
5. Evaporate solvents at reduced pressure and with gentle water bath heat (50C tops) - do not attempt to recover!
6. Dissolve the oily residue in water and then add saturated Sodium Carbonate solution until a white solid precipitates.
7. Filter this cake of white solid on the Buchner, then wash twice with ice cold water and dry in a vacuum dessicator.
8. Recrystallize the crude dried product from Benzene to yield ~63%.
9. *OPTIONAL* - Form the hydrochloride salt by bubbling HCl gas though the Benzene until white crystals fall out or shaking with 5% HCl and evaporating the water off.

References

1. Journal of Forensic Sciences, v34, #4, 1989, "The Stereoisomers of 4-Methylaminorex", pp 963-979, Klein, Sperling, Cooper & Kram
2. Journal of Medicine Chemistry, v6, 1963, "2-Amino-5-Aryl-2-Oxazolines. Potent New Anorectic Agents", pp 266-272, Poos, Carson, Rosenau, Roszkowski, Kelley & McGowin
3. Euphoria Document @ http://hyperreal.org/drugs/